Radio Shack PRO-136 Manuel d'utilisateur

Thank you for purchasing your 200 Channel Desktop Radio Scanner from RadioShack. Please read this user’s guide before installing, setting up and using

10Scanner Setup2. The hour digits flash. Press T or S or press the number keys to enter the hour. Then press ENT/PROGRAM to set.3. The minutes digits fl

11Scanner SetupBANK 1 PGMDLYExample shows entering bank 1 channel 00.Note: If you entered an invalid bank or channel number, Errorappears and the

12SearchingSearchingUse the search function to find active frequencies.While doing a fine tune or service bank search, press •/CLR/DELAY to turn the 2-s

13SearchingStoring Frequencies Found During a SearchTo store frequencies you find in a fine tune or service bank search:1. Press PSE at the frequency yo

14Searching3. Press L/O. L/O disappears.To clear all skipped frequencies at once:1. While searching, press PSE.2. Hold down L/O until the scanner beep

15ScanningScanningScanning Stored ChannelsPress SCAN/MAN to begin scanning your programmed frequencies. SCANscrolls across the display and the scanner

16ScanningTo stop at a channel while scanning:1. Press SCAN/MAN to stop scanning.2. Press T or S to select the next or previous channel. 3. Press SCAN

17ScanningWhen the scanner receives a SAME-coded signal, ALERT flashes and the SAME alert level appears, alternating with the weather channel. The scan

18Scanning PGM WX3. Press T or S to select F0 to F14. If a FIPS code is not programmed, ------- appears.4. Use the keypad to enter

19ScanningNote: Before using this feature, enter the local Skywarn frequency for your area into Bank 9, Channel 19. (See “Programming Frequencies into

2ContentsScanner Setup ... 4Scanner Features ...

20SettingsSettingsSetting DelaySometimes a radio user might pause before replying to a transmission. To avoid missing a reply on a specific channel, th

21SettingsTo remove the lockout from a channel, manually select the channel, then press L/O. L/O disappears.To unlock all channels in the selected ban

22Advanced ProgrammingAdvanced ProgrammingYou can clone your scanner by transferring the programmed data to or from another PRO-136 scanner using a co

23Advanced ProgrammingCLONE and transfer progress are displayed on the slave unit. BANK0 1 2 3 PGM 5. When the data transf

24Additional InformationAdditional InformationFCC NoticeYour scanner might cause radio or TV interference even when it is operating properly. To deter

25Additional Informationpick up transmissions that are not legal to listen to. Doing so could subject you to legal penalties. We encourage responsible

26Additional InformationAM ... 20 dB S/N at 60% modulation25.0000-27.9950...

27Additional InformationTroubleshootingProblem Cause SolutionScanner is on but will not scan.SQUELCH is not adjusted correctly. Adjust SQUELCH.Only on

20-136Printed in China UBZZ01354ZZ(0)03A08Hypersearch, Hyperscan, and Adaptaplug are trademarks used by RadioShack Corporation.Limited One-year Warran

3ContentsReceiving NWR-SAME and Weather Alert Signals...16Turning On the Digital Weather Alert Feature...

4Scanner SetupScanner SetupScanner Features•/ CLR / DELAYEnter a decimal point. Clear an entry. Turn delay on or off.Select a service band: MAR (Marin

5Scanner Setup0-9Input a number.PRI (Priority) / WX ALERTTurns the priority function on or off. Press to turn weather alert on and off.L/OLockout sele

6Scanner SetupConnecting the AntennaAttach the supplied antenna to the scanner by aligning the arrow on its base with the tab on the scanner’s BNC con

7Scanner SetupBattery Notes• Use fresh alkaline AA batteries. • Rechargeable batteries can be used, but battery life is shorter than with alkaline bat

8Scanner SetupConnecting HeadphonesFor private listening, you can plug a mono earphone or headset into the Headphone Jack on the back of your scanner.

9Scanner SetupBesides searching within a selected frequency range, you can also search your scanner’s service banks. Service banks are preset groups o